RFID Reader am Arduino: Unterschied zwischen den Versionen

Aus eLAB Wiki
Wechseln zu: Navigation, Suche
(Programm für den Arduino)
 
Zeile 9: Zeile 9:
 
== Programm für den Arduino ==
 
== Programm für den Arduino ==
  
Das Arduino Programm initialisiert das RFID Modul und gibt Information des RFID Chip über die [[UART |serielle Schnittstelle]] aus.
+
Das Arduino Programm initialisiert das RFID Modul und gibt Information des RFID Chip über die [[UART |serielle Schnittstelle]] aus. Das Programm benötigt die MFRC Bibliothek. Hinzufügen über:
 +
Sketch | Bibliothek einbinden | Bibliotheken verwalten | Suche nach: MRFC522
 +
 
  
 
<syntaxhighlight lang="Arduino">
 
<syntaxhighlight lang="Arduino">

Aktuelle Version vom 10. Mai 2018, 11:49 Uhr

Anschluss des RFID-RC522 an den Arduino

zum Anschluss des RFID-RC522 RFID Moduls an ein Arduino Board werden die 5 I/Os benötigt, die SPI I/Os SS;SCK;MOSI MISO und ein Rest Pin.

RFID-RC522 Verdrahtung

RFID-RC522 Schaltplan

Programm für den Arduino

Das Arduino Programm initialisiert das RFID Modul und gibt Information des RFID Chip über die serielle Schnittstelle aus. Das Programm benötigt die MFRC Bibliothek. Hinzufügen über:

Sketch | Bibliothek einbinden | Bibliotheken verwalten | Suche nach: MRFC522


/*
 * -----------------------------------------------------------------------------
 * Example sketch/program showing how to read data from a PICC to serial.
 * -----------------------------------------------------------------------------
 * This is a MFRC522 library example; for further details and other examples see: https://github.com/miguelbalboa/rfid
 * 
 * Example sketch/program showing how to read data from a PICC (that is: a RFID Tag or Card) using a MFRC522 based RFID
 * Reader on the Arduino SPI interface.
 * 
 * When the Arduino and the MFRC522 module are connected (see the pin layout below), load this sketch into Arduino IDE
 * then verify/compile and upload it. To see the output: use Tools, Serial Monitor of the IDE (hit Ctrl+Shft+M). When
 * you present a PICC (that is: a RFID Tag or Card) at reading distance of the MFRC522 Reader/PCD, the serial output
 * will show the ID/UID, type and any data blocks it can read. Note: you may see "Timeout in communication" messages
 * when removing the PICC from reading distance too early.
 * 
 * If your reader supports it, this sketch/program will read all the PICCs presented (that is: multiple tag reading).
 * So if you stack two or more PICCs on top of each other and present them to the reader, it will first output all
 * details of the first and then the next PICC. Note that this may take some time as all data blocks are dumped, so
 * keep the PICCs at reading distance until complete.
 * 
 * @license Released into the public domain.
 * 
 * Typical pin layout used:
 * -----------------------------------------------------------------------------------------
 *             MFRC522      Arduino       Arduino   Arduino    Arduino          Arduino
 *             Reader/PCD   Uno/101       Mega      Nano v3    Leonardo/Micro   Pro Micro
 * Signal      Pin          Pin           Pin       Pin        Pin              Pin
 * -----------------------------------------------------------------------------------------
 * RST/Reset   RST          9             5         D9         RESET/ICSP-5     RST
 * SPI SS      SDA(SS)      10            53        D10        10               10
 * SPI MOSI    MOSI         11 / ICSP-4   51        D11        ICSP-4           16
 * SPI MISO    MISO         12 / ICSP-1   50        D12        ICSP-1           14
 * SPI SCK     SCK          13 / ICSP-3   52        D13        ICSP-3           15
 */

#include <SPI.h>
#include <MFRC522.h>

#define RST_PIN         9          // Configurable, see typical pin layout above
#define SS_PIN          10         // Configurable, see typical pin layout above

MFRC522 mfrc522(SS_PIN, RST_PIN);  // Create MFRC522 instance

void setup() {
	Serial.begin(9600);		// Initialize serial communications with the PC
	while (!Serial);		// Do nothing if no serial port is opened (added for Arduinos based on ATMEGA32U4)
	SPI.begin();			// Init SPI bus
	mfrc522.PCD_Init();		// Init MFRC522
	mfrc522.PCD_DumpVersionToSerial();	// Show details of PCD - MFRC522 Card Reader details
	Serial.println(F("Scan PICC to see UID, SAK, type, and data blocks..."));
}

void loop() {
	// Look for new cards
	if ( ! mfrc522.PICC_IsNewCardPresent()) {
		return;
	}

	// Select one of the cards
	if ( ! mfrc522.PICC_ReadCardSerial()) {
		return;
	}

	// Dump debug info about the card; PICC_HaltA() is automatically called
	mfrc522.PICC_DumpToSerial(&(mfrc522.uid));
}